Unfortunately, the service life in the refrigerator, declared by the manufacturer, doesn't generally correspond for the actual period of operation with the device with out repair. Among the many malfunctions that occur more than time inside the refrigerator, the most frequent is really a violation from the low temperature regime. Most normally this occurs as a result of wear of the sealing rubber, which demands to become replaced. Get more info about уплотнители для холодильников купить
Replace the seal in the refrigerator
The failure on the seal results in a rise in temperature inside the chambers on the refrigerator, which negatively impacts its operation. Over time, the seal can deform and even burst in an inconspicuous spot. Through these holes, warm air begins to penetrate into the freezer and refrigerator. Certainly, an insignificant defect won't greatly affect the shelf life from the products, but the unit’s service life straight is determined by the tight fit on the sealant for the body, simply because within a continuous fight against swiftly increasing temperatures, the refrigerator will have to begin the compressor more frequently.
To check the clearance in between the refrigerator physique along with the seal, take a strip of paper as much as 0.2 mm thick. Using a tight and correct fit of rubber to metal, the sheet won't move freely from side to side
Very first help
Should you find that the seal is deformed, try to resuscitate it. To perform this, heat the elastic far more strongly using a hairdryer (as much as 70 degrees) and slightly stretch within the location exactly where the gap is detected. Then close the door tightly and wait for the seal to cool.
In the event the deformation is huge, soak the rubber in hot water. To do this, carefully, avoiding tears, eliminate the rubber from the door and return right after the water bath to its location.
The best way to replace a gasket pressed under the door trim
Using a thin screwdriver, gently pry the edge with the lining and slowly eliminate the seal, becoming careful not to damage it. Then set up a brand new seal. In this case, raise the edges from the plastic with one screwdriver and push the rubber edge into place with all the other.
When you bought a repair seal, you may notice that it already has a challenging edge that simply fits beneath the lining. In the event the edge has a thickening, it should be cut using a sharp knife at a distance of about 10 mm from the edge. So that you can additional reliably repair the seal in place, a little bit superglue is often dripped onto the sections of its fit.
Replacing foam-sealed sealant
To remove the seal you will need:
A sharp knife; - self-tapping screws.
Get rid of the refrigerator door and location it on a steady, level surface with all the inside facing up. Use a sharp knife to visit the joint among the rubber and the body and remove the old seal. Clean the resulting groove of the remaining foam to make sure a snug match on the body of the new seal.
Drill holes for screws along the perimeter from the door in increments of about 13 cm. Cut the new seal for the preferred length, lay it inside the groove and fix it with screws. To resume the complete operation from the refrigerator, place the door in place and adjust the evenness in the seal using canopies.
Normally, gum replacement on the refrigerator door is needed. This sort of breakdown is most common amongst older models.
Amongst the several failures leading to a malfunction with the cooling gear, essentially the most typical would be the malfunctioning in the seal.
Modern technology is just not immune from the look of this trouble. Generally, the essence in the problems will depend on improper installation on the factory conveyor or might be acquired with careless use in everyday life. Improper operation can cause any equipment to malfunction. When the gum is damaged inside the refrigerator, the temperature regime modifications.To repair the issue, the compressor runs at full power.
All this may result in a malfunction on the refrigerator motor. The service center for the repair of household appliances will supply an enormous repair bill. To prevent such a nuisance, you should carefully monitor your refrigeration equipment.
The principle sign of malfunctioning the seal is viewed as a loose match of your door. If you doubt the correct operation of your gum, then you can verify this using a basic experiment. You'll need to take a strip of plain paper. Subsequent, open the refrigerator door and place paper on the seal itself. Just after that, we close it, leaving a smaller component outside.
