If your water heater is not working properly, you can call the professionals at Water Heater Repair Henderson to take care of the problem. Whether your water heater is gas or electric, or you have a tankless unit, Henderson Water Heater Repair can help. The professionals at Henderson Water Heater Repair are experts at solving problems with water heaters.
Problems with the pilot light
If you experience trouble lighting the pilot light in your water heater, you are not alone. A water heater's pilot light can go out for several reasons, from sediment buildup to an intermittent or unreliable light. Proper maintenance is essential to prevent these issues and extend the life of your water heater. Fortunately, most water heaters can be serviced easily by homeowners.
One of the most common causes of a failing pilot light is incorrect gas pressure. In this case, you should contact your gas company and ask them to check your gas pressure. Another reason for a failed pilot light is a clogged pilot light tube. This can be caused by dirt in the gas line. To fix this problem, a gas technician can install a dirt trap.
Sometimes, soot and carbon deposits can build up on the pilot light electrode. If you see a buildup, clean the tip of the electrode with a dry cloth or sandpaper. You can also check the gas valve to see if it is leaking. The gas supply might be cut off due to leakage or a malfunctioning regulator. Another common cause of a failed pilot light is an improper gas valve or a malfunctioning gas line. Air in the gas line can also prevent the pilot from lighting. Another cause may be a thermostat ECO switch.
If the pilot light is out of fuel, the heat generated by the water heater is not enough. This could result in a number of problems. Some problems can be solved simply by replacing the pilot light with a new one. The pilot light should be blue in color, but a yellow flame may indicate that the pilot is not working properly. You should also make sure that the water tank is filled completely before lighting the pilot light.
Problems with the thermostat
The thermostat in your water heater may not be working correctly. In this case, you will need to replace it. The thermostat is found in the upper heating element of the water heater. To replace it, follow the steps below. First, disconnect the power from the heater. Next, use a Phillips head screwdriver to remove the upper access panel. After that, you will need to fold away the protective cover and insulation to expose the thermostat. Next, disconnect the wiring. After removing the old thermostat, you must replace it with the new one.
Another common problem with a water heater thermostat is the water heater's inability to heat water quickly enough. The thermostat may not be properly set to 120 degrees Fahrenheit. If the temperature is low enough, you may need to buy a bigger water heater with a higher thermostat setting. You may also need to replace the thermocouple or replace the dip tube.
Another way to troubleshoot a water heater thermostat is to reset the unit. To do this, open the access panel on the front of the water heater. Once you've done this, you can test the thermostat's reset button. You can use a multimeter to check for continuity, which is a good indicator that the thermostat is working properly.
A water heater thermostat is an integral part of your water heater. A broken thermostat can lead to elevated energy bills and a shortened lifespan of the unit. In addition to causing the water to run cold, a broken thermostat can damage the heating element.
Problems with the anode rod
When your water heater is experiencing problems, you may suspect that the anode rod has failed. There are several signs that you should look for, including a rusty smell, a discolored water, and intermittent operation. In addition, the rod itself may be corroding. If you notice one of these problems, it may be time to have it replaced.
Before attempting to remove the anode rod, you should make sure that the tank is cold. The anode rod must be removed before a hot water supply can be turned on. To remove the anode, unscrew the two-bolt assembly. Then unscrew the anode rod from the bolt with a wrench.
The anode rod is an important safety feature that protects the water heater from corroding. When damaged, it can cause a leak or burst, which could lead to thousands of dollars in damages. In these cases, it's important to replace the anode rod before it fails completely.
A damaged anode rod can damage the tank's interior lining. It's also possible for the anode to fall to the bottom of the tank, mixing aluminum with the hot water. This results in an unpleasant taste and odor. Replacing the anode rod is a simple process, but you must be aware of the risks involved. Just be sure to use the right tools and keep enough overhead clearance to avoid damage to the new anode.
The anode rod in your water heater will wear out faster the more you use it. Fortunately, it is relatively inexpensive to replace the sacrificial anode rod. It's best to check the rod at least every four to six months.
Cost of repairs
If your water heater breaks down in Henderson, you may need to hire a professional to repair it. This repair can restore your hot water, and save you money in the long run. However, it is important to understand that you may need to pay for a permit or inspection. These charges are usually separate from the labor cost.
A valve that controls the pressure inside your water heater can be a small, inexpensive part to repair. The valve can be adjusted or replaced if it is leaking. If the valve is damaged or wears down, the whole system may be at risk of bursting. Other parts of the heater can require replacement, including the regulator and valves.
A new anode rod can increase the life of your water heater by as much as $100. Replacing an anode rod may be the most affordable solution, but it isn't cheap. You'll need to spend at least $100 to get a new one, but if the problem persists, you may need to spend an additional $200 or $300.
If you're concerned about the safety of your water heater, it's important to install earthquake straps. These heavy-duty straps can prevent a water heater from tipping over during an earthquake. Licensed plumbing professionals can install them for you for a reasonable price. The straps are also required by local plumbing codes.
Another major part of a water heater that needs repair is the tank. The tank can cost from $250 to $1,000. The tank is the storage portion of the water heater and it can get corroded, which can be expensive.
When to call a professional
If you're having problems with your water heater, it's time to call a professional. The problem might be a simple drain or clogged pipe, but it can also lead to a major water problem, like flooding. No matter the situation, it's best to partner with a plumber who's experienced and trustworthy. Plumbing professionals can provide emergency service, and many of them work 24 hours a day.
A professional water heater repair Henderson service will diagnose the issue and fix it in a timely manner. Generally, it's cheaper to call a professional than to attempt a DIY repair. They'll also have the knowledge to obtain a permit if needed. Additionally, they'll know if you need a bigger tank.
If you can't get hot water, the first thing to check is whether the pilot light is lit. In most cases, an extinguished pilot light is the primary cause of no hot water. Besides checking the pilot light, there could also be a broken thermostat, which you can reset to a higher temperature.
If you don't feel that your water heater is working properly, you may want to consider replacing it. Many tank-type water heaters have a lifespan of about ten years. However, some models are even older. You should check the manufacturer date stamp inside the tank to find out if your current unit is outdated.
